mobi
 
 
Current location:Home > Blogs > Technical documentation >
 

NewsDetails

 

Understanding ANSI B16.5 Flange Standards

author:David Miller time:2026-11-21 19:50:58 Click:0

ASME B16.5 is the most widely cited standard for pipe flanges. It ensures flanges from different manufacturers are interchangeable in dimensions, pressure rating and bolting.

1. What Does B16.5 Cover?

The standard covers flanges from NPS 1/2 through NPS 24, in classes 150 through 2500. It specifies dimensional tolerances, facing dimensions, pressure-temperature ratings and material requirements.

Carbon Steel Flange

2. Key Dimensions

  • Outside diameter of the flange.
  • Bolt circle diameter and number/size of bolts.
  • Bore diameter matching the pipe schedule.
  • Raised face height and surface finish.

3. Face Types

  • Raised Face (RF) — most common, 1/16 inch raised face for classes 150/300.
  • Flat Face (FF) — used for cast iron and low-pressure applications.
  • Ring Type Joint (RTJ) — for high pressure and high temperature services.

4. Why It Matters

Specifying B16.5 ensures your flanges will mate with valves, pumps and equipment from any manufacturer. Always state the standard, class, face type, material and NPS on the purchase order.

Flange Face Finish and Gasket Performance

The flange face finish (roughness) affects gasket performance. RF faces typically have a 125–250 AARH roughness. Too smooth and the gasket cannot bite; too rough and it leaks. Always specify the required surface finish on the flange drawing.

Flange Face Finish and Gasket Performance

The flange face finish (roughness) affects gasket performance. RF faces typically have a 125–250 AARH roughness. Too smooth and the gasket cannot bite; too rough and it leaks. RTJ faces are machined to a specific finish for metal ring gaskets. Always specify the required surface finish on the flange drawing.

Gasket Materials and Applications

Gasket material selection is critical for leak-free performance. Common materials include: elastomers (NBR, EPDM) for water and low pressure; spiral wound (SS + graphite/PTFE) for general industrial; ring joint (octagonal/oval steel) for high pressure RTJ; and non-asbestos sheet for low pressure. Match the gasket material to the fluid, temperature and pressure. Never reuse a gasket — always install a new one during maintenance.

Gasket Type Material Best For
Spiral WoundSS windings + graphite/PTFE fillerGeneral industrial, high temp
Ring JointSoft iron, SS, monelHigh pressure RTJ flanges
ElastomerNBR, EPDM, VitonWater, low pressure, food grade
Non-Asbestos SheetAramid fiber + NBRLow pressure, general service

ANSI B16.5 Flange FAQ

Answers to the most common questions about ANSI B16.5 flange standards.

  • What is ANSI B16.5? — ANSI B16.5 (now ASME B16.5) is the standard for pipe flanges and flanged fittings from 1/2 inch to 24 inches. It covers dimensions, materials, pressure ratings and testing requirements.
  • What pressure classes are covered? — ASME B16.5 covers Class 150, 300, 400, 600, 900, 1500 and 2500. The most commonly used are Class 150 and Class 300 for general industrial service.
  • Which flange materials are covered? — Common materials include carbon steel (A105), stainless steel (304/316), alloy steel (F11, F22) and duplex stainless. Each material has its own pressure-temperature rating table.
  • Are B16.5 flanges compatible with BS or DIN flanges? — They are dimensionally different and not directly interchangeable. Always specify which standard you are using. If you need to connect different standards, use a transition flange.
  • How are flanges marked? — Each flange is marked with: manufacturer's mark, material grade, pressure class, size, and heat number. The marking ensures traceability and compliance with the standard.

B16.5 vs B16.47: Which Standard?

ASME B16.5 covers flanges up to 24 inches. For larger sizes (26–60 inches), use ASME B16.47 (Large Diameter Steel Flanges). B16.47 has two series: Series A (formerly MSS SP-44) and Series B (formerly API 605). They are not interchangeable — specify which series you need.

Writer Robert Taylor

Robert Taylor is a technical writer and engineer with over 12 years of experience in the industry. He specializes in technical documentation, product specification and application engineering. Robert Taylor holds a Bachelor's degree in Mechanical Engineering and has contributed to numerous technical publications on pipeline design, corrosion protection and industrial solutions.

联系 Contact us

——  Contact:Manager

——  Tel:+86 15231788966

——  Email:info@zhantongpipe.com

——  Url:https://www.zhantongpipe.com

——  Address:Mengcun Hui Autonomous County, Cangzhou City, Hebei Province

contact usAddress:Mengcun Hui Autonomous County, Cangzhou City, Hebei Province
contact usMobile:+86 15231788966
contact usWhatsapp:+86 15231788966
Copyright © 2025-2026 https://www.zhantongpipe.com. All Rights Reserved Hebei Zhantong Pipeline Equipment Manufacturing Co., Ltd
Mobile terminal
contact